7.6-Up-Down Counter | Goeduhub Technologies

Autoplay
Autocomplete

Previous Lesson Complete and Continue

Learn Fuji PLC Programming From Scratch

Overview of PLC

1.1 Introduction to PLC (5:54)
1.2 Block Diagram of PLC (3:46)
1.3 Working Principle of PLC (Scan Time and Scan Cycle of PLC) (7:32)
1.4 What is Sink and Source concept (11:34)
1.5 PNP and NPN wiring of sensor with PLC (Example Sink and Source Input) (13:25)
1.6-Wiring Connection and Communication of PLC (8:54)

Basics of FUJI PLC

2.1-Introduction to FUJI PLC (3:24)
2.2-Functions and features of FUJI PLC (8:28)
2.3-Software Interface of WinProladder (5:45)
2.4-Data types in FUJI PLC (7:42)
2.5-Addressing Format in FUJI PLC (19:23)

Basics of Ladder diagram

3.1-The IEC 1131 STANDARD and Programming Language (9:24)
3.2-Bit Logics (NO Type) (10:53)
3.3-Bit Logics (NC Type and Output Coil) (9:58)
3.4-Basic Programming Rule 1 (1:48)
3.5-Basic Programming Rule 2 (2:35)
3.6-Basic Programming Rule 3 (2:16)
3.7-Basic Programming Rule 4 (2:20)
3.8-Basic Programming Rule 5 (1:22)
3.9-Basic Programming Rule 6 (1:30)
3.10-First program in WinProladder (14:05)
3.11-Problem 1 With Solution (22:09)
3.12-Problem 2 With Solution (9:38)
3.13-Problem 3 With Solution (8:50)
3.14-Ladder Logic Program for Boolean Expression (8:01)
3.15-Logic Gates (AND & OR Gate) (8:09)
3.16-Logic Gates ANDOR Gate in Software (6:24)
3.17-Logic Gates (NAND & NOR Gate) (10:18)
3.18-Logic Gates NANDNOR Gate in Software (5:59)
3.19-Logic Gates (EX-OR & EX-NOR Gate) (11:30)
3.20-Logic Gates EX-OR EX-NOR Gate in Software (6:44)
3.21-Positive And Negative Transition Input (15:43)
3.22-Differential Up(DIFU) And Difeerential Down(DIFD) Output (6:49)

Latching and Unlatching

4.1-Introduction to Latching (Holding) and Unlatching Concept (12:02)
4.2-Latching (Holding) and Unlatching Concept in Software (14:54)
4.3-Latching and Unlatching Problem-1 (3:43)
4.5-Latching and Unlatching Problem-1 Solution in Software (6:00)
4.4-Latching and Unlatching Problem-1 Solution in Software (11:16)
4.6-Introduction of Set and Reset Instruction (11:07)
4.7-Set and Reset Instruction in Software (6:55)

Interlocking

5.1-Interlocking Concept (11:00)
5.2-Interlocking Concept in Software (13:54)

Timer

6.1-Introduction to Timer (17:39)
6.3-Different Types Of Timer In WinProladder (20:22)
6.5-0.1S Timer (12:50)
6.6-1S Timer (8:37)
6.7-How To Provide Variable Time Delay (11:18)
6.8-How To Stop Currentt Value Upto Preset Value (4:38)
6.9-Problem1 With Solution (14:54)
6.10-Problem2 With Solution (11:15)
6.11-Problem-3 (Traffic Light) (2:08)
6.12-Problem-3 Solution Explanation (9:41)
6.13-Problem-3 Solution Part-2 (8:14)
6.14-Accumulative(Retentive Timer) (14:07)

Counter

7.2-Different Types Of Counters In WinProladder (5:31)
7.1-Introduction of Counter (7:49)
7.3-16-Bit Counter Part1 (16:52)
7.4-16-Bit Counter Part2 (10:23)
7.5-32-Bit Counter (3:52)
7.6-Up-Down Counter (11:49)

Data Transfer Instruction

8.1-MOV,DMOV,PMOV,DPMOV (13:19)

Output Terminal Compare Instruction(Unsigned)

9.1-COMPARE(CMP,DCMP,PCMP,DPCMP) (13:28)

Input Terminal Compare Instruction (Signed)

10.1-Input Type Comparison (13:52)

Increase/Decrease Instruction

11.1-INCREMENT1D1P1DP (12:52)
11.2-DECREMENT1D1P1DP1 (11:49)

Calculation Instruction

12.1-ADDITIONDPDP (17:03)
12.2-ADDITIONDPDPParT-2 (10:25)
12.3-SUBTRACTIONDPDP (14:48)
12.4-MULTIPLICATION (12:02)
12.5-DIVISION (10:52)

Program or Sequence Control Instruction And Subroutine

13.1-Introduction of Sequence Control Function (10:03)
13.2-Jump(JMP) Instruction (10:48)
13.3-SKIP(SKP) And SKIP END(SKPE) (10:20)
13.4-Introduction of Subroutine Instruction (11:05)
13.5-Subroutine in (CALL,LBL,RTS) (15:00)
13.6-END Instruction (6:52)

Master Control/Master Control End

14.1-Master Control Start(MC) And Master Control End(MCE)-part1 (14:04)
14.2-Master Control Start(MC) And Master Control End(MCE) Part-2 (4:32)

Teach online with

7.6-Up-Down Counter

Lesson content locked

If you're already enrolled, you'll need to login.

Enroll in Course to Unlock