2.2 Functions and features of Delta PLC | Goeduhub Technologies

Autoplay
Autocomplete

Previous Lesson Complete and Continue

Complete course on WPLSOFT for DELTA PLC Programming

Overview of PLC

1.1 Introduction to PLC (5:54)
1.2 Block Diagram of PLC (3:46)
1.3 Working Principle of PLC (Scan Time and Scan Cycle of PLC) (7:32)
1.4 What is Sink and Source concept (11:34)
1.5 PNP and NPN wiring of sensor with PLC (Example Sink and Source Input) (13:25)
1.6 Wiring Connection and Communication of Delta PLC (8:04)

Basics of Delta PLC

2.1 Introduction to Delta PLC (1:57)
2.2 Functions and features of Delta PLC (7:21)
2.3 Software Interfacing and First Program in Delta PLC (10:52)
2.4 Addressing Format in Delta PLC (9:15)

Bit Logic and Logic Gates

3.1 Bit Logics (NO Type) (10:53)
3.2 Bit Logics (NC Type and Output Coil) (9:58)
3.3 Basic Programming Rule 1 (1:48)
3.4 Basic Programming Rule 2 (2:35)
3.5 Basic Programming Rule 3 (2:16)
3.6 Basic Programming Rule 4 (2:20)
3.7 Basic Programming Rule 5 (1:22)
3.8 Basic Programming Rule 6 (1:30)
3.9 Problems-1 with Solution (6:34)
3.10 Problems-2 with Solution (8:29)
3.11 Problems-3 with Solution (6:55)
3.12 Problems-4 with Solution (4:46)
3.13 Ladder Logic Program for Boolean Expression (8:01)
3.14 Logic Gates (AND & OR Gate) (8:09)
3.15 Logic Gates (AND & OR Gate) in Software (9:11)
3.16 Logic Gates (NAND & NOR Gate) (10:18)
3.17 Logic Gates (NAND & NOR Gate) in Software (6:29)
3.18 Logic Gates (EX-OR & EX-NOR Gate) (11:30)
3.19 Logic Gates (EX-OR & EX-NOR Gate) in Software (6:33)

Latching and Unlatching

4.1 Introduction to Latching (Holding) and Unlatching Concept (12:02)
4.2 Latching (Holding) and Unlatching Concept in Software (9:16)
4.3 Latching and Unlatching Problem-1 (10:19)
4.4 Latching and Unlatching Problem-1 in Software (8:54)
4.5 Introduction of Set and Reset Instruction With in Software (13:36)

Interlocking

5.1 Interlocking Concept (11:00)
5.2 Interlocking Concept in Software (11:09)

Timer

6.1 Introduction to Timer (14:48)
6.2 Timer in Software (11:44)
6.3 Problem-1 with Solution in Software (14:42)
6.4 Problem-2 Explanation (2:13)
6.5 Problem-2 with Solution in Software (8:36)

Counter

7.1 Introduction of Counter Part-1 (4:42)
7.2 Introduction of Counter Part-2 (5:36)
7.3 Problem-1 with Solution in Software (13:10)

Compare Instruction (= =, , > =, and

8.1 Introduction of Compare Instruction Part-1 (5:16)
8.2 Introduction of Compare Instruction Part-2 (4:55)
8.3 Introduction of Compare Instruction Part-3 (1:44)
8.4 Contact Type Compare Instruction Part-1 (6:42)
8.5 Contact Type Compare Instruction Part-2 (4:22)
8.6 Zone Compare Instruction (7:30)

Mathematical Instruction

9.1 Introduction of Mathematical Instruction (1:12)
9.2 Addition Instruction (18:45)
9.3 Subtraction Instruction (7:20)
9.4 Multiplication Instruction (5:57)
9.5 Division Instruction (5:40)

Move Instruction

10.1 Introduction of Move Instruction with in Software (6:38)

Program Control Instruction

11.1 Introduction of Program Control Instruction (4:48)
11.2 Conditional Jump Instruction with in Software (10:08)
11.3 MCR (Master Control Relay) Instruction with in Software (7:52)
11.4 Subroutine Instruction with in Software (11:21)

Teach online with

2.2 Functions and features of Delta PLC

Complete and Continue